Foundry & Investment Casting
Silanes for Acid-Cured No-Bake Sand
Good no-bake sand needs a usable molding window and enough strength for stripping, handling and storage. Silanes for acid-cured no-bake sand help you develop the contact between silica grains and a compatible furan or phenolic binder while keeping these production stages in view.
LANDUSIL supplies amino and ureido silanes for binder formulators and foundries working on sand–resin adhesion and humidity-conditioned strength. Select the organic functionality, alkoxy chemistry and addition route around your actual resin, acid hardener and sand supply.

What Silanes for Acid-Cured No-Bake Sand Do
- Develop the mineral–resin interface. Hydrolyzable silane groups provide a route to the silica surface, while the organic group interacts with a compatible binder.
- Target humidity-sensitive bonding. Interface development helps address the grain–binder contact when it is the weak point during humid storage.
- Offer different nitrogen-functional routes. Primary-amino, ureido and bis-silylamine structures let you compare resin compatibility and interface response.
- Fit two practical addition routes. You can develop a controlled sand pretreatment or incorporation through a compatible resin stream.
- Connect formulation to handling needs. Select against the strength needed at stripping and transfer, as well as later dry and conditioned strength.
Typical Uses
End use: Furan no-bake molds and cores
What matters most
Acid-cure response, usable work time and retained strength after humid storage
End use: Acid-cured phenolic no-bake molds
What matters most
Early lifting and assembly strength with the actual resin delivery conditions
End use: Fresh and reclaimed silica-sand blends
What matters most
Grain distribution, fines, moisture, acid demand and residual binder chemistry
End use: Resin blends stored before mixing
What matters most
Initial compatibility and sand properties obtained after resin-blend aging
End use: Cores receiving refractory coatings
What matters most
Strip readiness, coating carrier, drying sequence and subsequent handling
Recommended LANDUSIL Products
| Product | Chemistry | CAS | Why choose it |
|---|---|---|---|
| LANDUSIL LEGRA 1010-L | 3-Aminopropyltriethoxysilane | 919-30-2 | Primary-amino ethoxy route for sand–resin coupling; assess its interaction with the acid-cure window |
| LANDUSIL LEGRA 7011-L | 3-Ureidopropyltrimethoxysilane | 23843-64-3 | Ureido-functional comparison for resin compatibility and stored-blend evaluation |
| LANDUSIL LEGRA 1011-L | 3-Aminopropyltrimethoxysilane | 13822-56-5 | Primary-amino methoxy option when developing the hydrolysis and conditioning sequence |
| LANDUSIL LEGRA 1071-L | Bis(3-trimethoxysilylpropyl)amine | 82985-35-1 | One secondary amine with two silane-bearing ends for a distinct interface comparison |
| LANDUSIL LEGRA 1021-L | N-(2-Aminoethyl)-3-aminopropyltrimethoxysilane | 1760-24-3 | Diamino structure where the additional amino functionality has a defined formulation role |
How to Select a Silane for Your No-Bake Binder
Start with the resin and acid hardener
Identify whether you use furan or acid-cured phenolic chemistry. Record the resin grade, water content where relevant, hardener and mixing procedure. Amino functionality can interact with an acidic formulation, so the useful comparison combines interface response with work and stripping behavior.
Keep sand acid demand alongside pH in your records. These measurements describe different aspects of the sand's response to the curing system. Include the prior binder and reclamation process when working with reclaimed silica sand.
Choose the nitrogen-functional structure
LEGRA 1010-L and LEGRA 1011-L each have one primary amine. LEGRA 1021-L has a primary and a secondary amine, while LEGRA 1071-L has one secondary amine and two silicon ends. LEGRA 7011-L supplies ureido functionality. Choose the structure to answer a specific compatibility or interface question.
Ethoxy groups release ethanol during hydrolysis; methoxy groups release methanol. Include water, released alcohol and the treatment's condition when comparing the two routes. Use a defined active-input basis for comparisons across structures and supply forms.
Match the ingredient to the addition point
For sand pretreatment, define the treatment medium, hydrolysis state, distribution, drying and storage. The treated sand entering the mixer should have a recorded moisture condition. For resin incorporation, follow the fresh blend and its properties after the intended storage period, then make sand specimens from both.
Application and Evaluation Guidelines
Begin with your established sand–resin–acid formulation. Keep sand temperature, grading, fines, moisture and reclaimed fraction steady while comparing the silane. State whether the input is based on sand, resin or active silane, and account for any carrier. Follow the binder supplier's mixing procedure; do not directly premix concentrated resin and acid hardener.
Measure workability after the actual mixer residence and transport delay. Follow stripping, early handling and later strength at ages relevant to the production sequence. For a humidity issue, distinguish curing in humid air from exposing a previously cured core. Record specimen geometry and conditioning history for both.
Include fresh and aged resin blends, plus the intended refractory coating and drying cycle. A clear initial resin blend does not establish storage compatibility. Record any hardener adjustment as another comparison so its cure effect remains visible. Confirm gas behavior, thermal response and casting quality in the relevant later trials; the silane is an interface ingredient, not a replacement resin or acid hardener.

Frequently Asked Questions
Which silanes are used in furan no-bake sand?
Amino and ureido silanes are useful starting directions for compatible formulations. Compare LEGRA 1010-L with LEGRA 7011-L using your resin, acid hardener and sand, then assess work time and humidity-conditioned strength together.
How should I add silane to a foundry resin binder?
Develop incorporation in a compatible resin stream and follow both fresh and stored blends. Sand pretreatment is another route, with its own hydrolysis, drying and moisture controls.
How much silane is needed for no-bake sand?
Set the trial input from the sand surface, binder chemistry and addition route. State the calculation basis and active content clearly, then use controlled comparisons to select the working level.
What should I measure when using reclaimed sand?
Record acid demand, pH, fines, moisture, temperature and prior binder history. Compare defined fresh/reclaimed blends through workability, stripping and conditioned strength.

Samples and Technical Support
LANDUSIL provides samples, TDS, SDS and selection support for acid-cured sand binder development. Please include:
- Furan or acid-cured phenolic resin and acid-hardener identity
- Sand analysis, acid demand and fresh/reclaimed ratio
- Addition sequence, resin-storage requirement and coating cycle
- Work-time, handling or humidity targets and comparison methods
- Estimated quantity, packaging preference and destination country

