Skip to content
Browse by chemistry
Need help choosing?

Mold release selection

How to Choose a Mold Release Agent: Silicone vs Non-Silicone, Semi-Permanent vs Sacrificial

A mold release agent forms a thin barrier between a mold and the part being molded, so the part separates cleanly without damage to either. The right choice depends on four questions: what you are molding and how, how hot the mold runs, how many releases you need per application, and whether the part will be painted, printed or bonded afterwards.

Published by LANDUSIL · Last updated November 2026

Material surface artwork representing low-surface-energy silicone formulations

This guide walks through the main types of release agents, the trade-offs between them, and how to narrow the choice for rubber, polyurethane, thermoplastic and composite molding.

The decision path at a glance

Start with what happens to the part after molding, then decide how often you want to apply, then match the carrier to your mold temperature.

Mold release decision pathIf the part will be painted, printed or bonded, prefer non-silicone or low-transfer release and validate cleaning. If not, choose sacrificial release for one or a few releases per application or semi-permanent release for many. Then match water-based or solvent-based carriers to mold temperature and cycle time.1. Will the part be painted,printed or bonded?Prefer non-silicone orlow-transfer release;validate cleaning in trials2. How many releasesper application?One or a fewSacrificialManySemi-permanent3. Match the carrierWater-based: lower VOC;needs a suitable moldtemperature to drySolvent-based: fastflash-off on coolermolds and short cyclesYesNo
A simplified selection path. Process trials confirm the final choice.

1. How mold release agents work

During molding, the material being shaped wets the mold surface and can adhere to it chemically or mechanically. A release agent prevents this by placing a low-surface-energy layer at the interface. A good release system delivers:

  • Clean, consistent release without tearing, distortion or sticking
  • The required surface finish on the part (gloss, matte or texture)
  • Low mold build-up, so cleaning intervals stay long
  • Minimal transfer to the part where downstream processes require it
  • Repeatable results from shift to shift

The best release agent is the one that balances these for your process—not the one that simply releases most easily.

2. Internal vs external release agents

Internal release agentsExternal release agents
How they workAdded to the molding compound; migrate to the surface during processingApplied to the mold surface by spray, wipe or brush
AdvantagesNo application step; consistent dosingFlexible; can be optimized per mold; no change to the formulation
LimitationsCan affect part properties, paintability or bonding; requires formulation workAdds an application step; coverage depends on operator and equipment
Typical useSome PU systems, sheet and bulk molding compounds, certain rubber and plastic compoundsMost rubber, PU foam, thermoplastic and composite molding

Many processes combine both: an internal agent reduces sticking while a light external application handles difficult areas.

3. Sacrificial vs semi-permanent release

Sacrificial vs semi-permanent release filmsLeft: a sacrificial film splits between mold and part, so it must be reapplied often. Right: a semi-permanent film is bonded to the mold and supports multiple releases with low transfer.SacrificialMoldMolded partFilm splits and transfers → reapply every cycle or few cyclesSemi-permanentMoldMolded partCured film stays on the mold → multiple releases, low transfer
Schematic only: film thicknesses are exaggerated for clarity.
Sacrificial (conventional)Semi-permanent
MechanismA film that is partly consumed or transferred with each partA thin film that cures or bonds to the mold surface
Releases per applicationOne or a fewMultiple releases before reapplication
Transfer to partHigherLower
Mold build-upCan build up over timeGenerally lower, with proper application
ApplicationSimple; frequentMore controlled: clean mold, correct cure, sealer where required
Typical chemistriesWaxes, silicone fluids and emulsions, soapsPolymer-based systems, including polysiloxane resins and other reactive chemistries

Semi-permanent systems are widely used in composite and high-volume molding, where reducing application frequency and part contamination pays off. They demand more discipline: the mold must be properly cleaned and the film fully cured before the first part.

Polysiloxane resins are one of the chemistries behind semi-permanent films. Learn more about NOVERA silicone resins.

Silver material artwork representing NOVERA silicone resins

4. Silicone vs non-silicone release agents

Silicone release agents—based on PDMS fluids, emulsions or silicone resins—are popular because of their very low surface energy, thermal stability and efficient release. Learn more about the chemistry in What Is PDMS? and What Are Silicones?

When silicone is a strong choice

  • High mold temperatures, such as rubber molding
  • Difficult releases and complex mold geometries
  • Processes where the part is not painted or bonded afterwards
  • Applications where a smooth, glossy surface is wanted

When to be careful with silicone

The same low surface energy that makes silicone release so effective can cause problems downstream. Silicone residue transferred to a part can lead to:

  • Cratering (“fish eyes”) or poor adhesion when the part is painted or coated
  • Reduced adhesive bond strength
  • Printing and decorating defects
  • Contamination of nearby paint or assembly areas through overspray

Non-silicone alternatives include wax-based, soap and fatty-acid-based, fluoropolymer-based and other polymeric release agents. They are the usual choice when parts must be painted, bonded or printed without extensive cleaning, or when the plant restricts silicone use.

The practical rule: define what happens to the part after molding before choosing the release chemistry. If downstream painting or bonding is required, test with the full process—including any cleaning or pretreatment step—before committing to a silicone release agent.

5. Water-based vs solvent-based

Water-basedSolvent-based
VOC and workplace safetyLower VOC; non-flammable carriersHigher VOC; flammability and ventilation controls
DryingNeeds sufficient mold temperature or time to evaporate waterFast flash-off, including on cooler molds
Film uniformityDepends on mold temperature: too cold and water evaporates slowly or pools; too hot and droplets can bounce off or dry before wettingGenerally easy to apply evenly across a wide temperature range
Regulatory trendIncreasingly preferredIncreasingly restricted in some regions

Water-based release agents (often silicone or wax emulsions) have become the default in many plants. Check that your mold temperature and cycle time allow the water to evaporate fully before the material is introduced, and adjust spray settings to the actual mold temperature.

6. Choosing by process

Rubber molding

Compression, transfer and injection molding of rubber typically run hot and involve compounds that adhere strongly to steel. Silicone emulsions are widely used, in both sacrificial and semi-permanent forms. Watch for build-up on the mold and for transfer if parts are later bonded to metal or painted. See Silicone for Rubber Mold Release.

Polyurethane foam

Molded PU foam is sensitive to the release agent, which can influence the foam skin, surface cells and appearance as well as release. Release systems are usually designed together with the foam chemistry and mold temperature. See Silicone for PU Foam Mold Release.

Cast polyurethane elastomers

Cast PU parts often need clean release from open or closed molds over long cure times, with a defined surface finish. See Silicone for Cast PU Mold Release.

Thermoplastics and injection molding

Thermoplastics usually release well from polished molds, so external release sprays are used selectively—for start-up, complex geometries or problem areas. Because many thermoplastic parts are later painted, printed or welded, check downstream compatibility first. See External Release for Thermoplastic Molding.

Composites

Composite molding commonly uses semi-permanent release systems on prepared molds, with sealers to control porosity, or release films in vacuum-bagging processes. Because composite parts are frequently painted or bonded, transfer and surface energy of the released part matter as much as the release itself. Browse all Industrial Release Agents applications.

7. Selection checklist

Before requesting a recommendation, collect the following:

  1. Molded material and grade – rubber compound, PU system, thermoplastic or composite resin
  2. Process – compression, injection, casting, foaming, lay-up, etc.
  3. Mold material and surface condition – steel, aluminum, composite tooling; polished, textured, worn
  4. Mold temperature range and cycle time
  5. Required releases per application – every cycle, or as few applications as possible?
  6. Part surface requirements – gloss, texture, appearance
  7. Downstream processes – painting, coating, bonding, printing, welding
  8. Application method – spray, wipe, brush, automated system
  9. VOC, workplace and regulatory requirements – including any plant restriction on silicone
  10. Current release agent and the problem to solve – sticking, build-up, defects, cost per part

8. Troubleshooting common release problems

ProblemPossible causesWhat to check
Part sticks to moldInsufficient coverage, worn film, mold temperature outside the range for a water-based agent, damaged mold surfaceApplication amount and pattern, reapplication interval, mold temperature, mold condition
Mold build-upExcess application, incompatible release agent, residues from the molding materialApplication rate, cleaning interval, switch to semi-permanent or a different chemistry
Uneven gloss or streaksNon-uniform film, overspray, release agent incompatible with the materialSpray setup, dilution, drying, compatibility
Craters or poor paint adhesionSilicone or other release residue on the partRelease chemistry, transfer level, part cleaning/pretreatment
Weak adhesive bondsTransferred release agent on bonding surfacesRelease chemistry, masking, surface preparation before bonding

9. Frequently asked questions

Can parts released with silicone be painted?

Sometimes, but it requires care. Silicone residue can cause cratering and poor adhesion. If parts will be painted, either choose a non-silicone or low-transfer release system, or validate a cleaning and pretreatment step as part of your process trials.

How often should a semi-permanent release agent be reapplied?

It depends on the product, molded material, mold temperature and part geometry. Establish the interval in production trials by tracking release force or sticking, and reapply before release starts to deteriorate.

What is the difference between a release agent and a release film?

A release agent is a liquid or paste applied to the mold or added to the compound. A release film is a separate sheet placed between the mold or bagging materials and the part, common in composite vacuum-bagging and pressing processes.

Are water-based release agents as effective as solvent-based ones?

In many processes, yes—provided the mold temperature suits the product and there is enough time for the water to evaporate. On cold molds or with very short cycles, solvent-based products may still be easier to apply evenly.

Should I use an internal or external release agent?

External release agents are more flexible and do not change the compound. Internal agents remove the application step but must be evaluated for effects on part properties, paintability and bonding. Many processes use a combination.

Choosing a release agent is a process decision, not just a product choice. Describe your molded material, mold temperature, release frequency and downstream steps to info@landusil.com to request technical information or a sample, or plan a structured trial through our Sample Evaluation service.

Discuss Your Release Application

Explore LANDUSIL