Agricultural Formulations
In-Can Silicone Adjuvants for Agrochemical Formulations
Incorporating a wetting or foam-control ingredient during formulation lets you build its function into the concentrate. In-can silicone adjuvants support this development route by addressing the receiving product during manufacture, storage and its transition into a diluted spray liquid.
For in-can formulation work, LANDUSIL offers two complementary materials: LANDUSIL SIVERA 4010-L, a polyether-modified silicone adjuvant, and LANDUSIL SIVERA 5010-L, a silicone defoamer. Select each around the active ingredient, continuous phase and existing auxiliary package.

What Silicone Adjuvants Do in Stored Formulations
- Introduce a wetting function into the concentrate. A silicone-polyether ingredient provides a route to develop leaf wetting after dilution.
- Address processing foam. A formulated defoamer targets bubbles generated by agitation, milling, transfer or filling.
- Connect manufacture with use. An incorporated ingredient can be followed through storage and dilution as part of the finished formulation.
- Support phase-specific selection. The active, water, solvent and dispersant package guide which ingredient role to investigate.
- Make functional comparisons clearer. Assigning wetting and foam control to identified components helps you interpret concentrate and spray-liquid behavior.
Typical Uses
End use: Aqueous solutions and soluble concentrates
What matters most
Dissolved active, electrolyte load, pH and temperature exposure
End use: Suspension concentrates and seed-treatment suspensions
What matters most
Manufacturing shear, solids distribution, rheology and redispersion
End use: Emulsions, microemulsions and suspoemulsions
What matters most
Existing interfaces and the combined liquid and solid dispersion requirements
End use: Oil-based concentrates and emulsifiable concentrates
What matters most
Distribution in the continuous phase and the transition on adding water
End use: Stored products prepared for spraying
What matters most
Retained active content, dilution behavior, foam and wetting after storage
Recommended LANDUSIL Products
| Product | Chemistry | CAS | Why choose it |
|---|---|---|---|
| SIVERA 4010-L | Polyether-modified silicone agricultural adjuvant | Mixture – see SDS | Wetting and spreading input for development within a defined concentrate and its dilution |
| SIVERA 5010-L | Silicone agricultural defoamer | Mixture – see SDS | Foam-control ingredient to assess during processing, storage and preparation of the diluted product |
How to Select In-Can Silicone Adjuvants
Define the continuous phase
Identify whether the added ingredient meets an aqueous, solvent-based or oil-based environment. Record the active ingredient's physical state, salts, pH and existing emulsifiers or dispersants. For a suspension, include the solid phase and its processing history; for an emulsion, describe the interfacial package.
This formulation description guides the initial comparison. A useful sample brief identifies the actual product composition and the function being added, even when several products share the same broad formulation code.
Choose wetting or foam control by task
Select SIVERA 4010-L when the project centers on diluted spray wetting and spreading. Define silicone antifoam incorporation around SIVERA 5010-L when foam is generated during manufacture or subsequent dilution. Where both functions matter, give each component an explicit task and retain the full emulsifier or dispersant system in the study.
Connect the incorporation point with processing
Describe the ingredient's exposure to shear, mixing and milling. For stored suspensions, follow its distribution through processing and recovery after settling. For oil-based formulations, follow incorporation into the continuous phase and the change that occurs when spray water is introduced.
Use Agricultural Foam Control for a closer look at manufacturing stages where bubbles affect handling and filling.
Application and Evaluation Guidelines
Plan agrochemical storage compatibility around three sampling stages. Carry an appropriate reference formulation through the same preparation, packaging and storage sequence as the test product.
| Sampling stage | Measurements to include |
|---|---|
| Fresh concentrate | Active content, appearance, physical state and baseline wetting or foam behavior |
| Concentrate after selected storage | Active retention, phase behavior, sediment, rheology and redispersibility as relevant |
| Dilution made from stored concentrate | Dispersion, foam, wetting and application behavior in the intended water |
Select storage exposure and thermal cycling for the actual product requirements. Record the container, time, conditions and recovery procedure. Include the concentrate and its dilution so the assessment follows both concentrate stability and the function delivered at use.
The actual silicone-polyether structure, carrier and active content require product-specific documentation. A generic family description does not establish a hydrolysis window, broad pH compatibility or a commercial shelf life. Visual clarity alone does not establish chemical retention, and a short tank-mix result cannot establish long-term in-can compatibility.
Confirm active content and relevant ingredient chemistry alongside physical measurements. Follow the diluted liquid through its intended holding period, including filter passage and deposited coverage where these are relevant. Assess crop response, efficacy and residues within the complete product's application program. The two ingredients provide wetting and foam-control functions, not a complete emulsifier or suspension package.

Frequently Asked Questions
Which silicone ingredient is used for in-can wetting?
SIVERA 4010-L provides a polyether-modified silicone wetting route for a defined agrochemical concentrate. Assess its behavior in the receiving formulation, then follow wetting and spreading in dilutions prepared from fresh and stored samples.
What should an in-can adjuvant storage study include?
Include the fresh concentrate, stored concentrate and dilution prepared from that stored material. Measure active-content retention and physical stability together with the intended wetting or foam-control function. Keep the reference formulation under matching exposure conditions.
How do I select an antifoam for a suspension concentrate?
Start with the solids, dispersant package, process shear and foam-generating stage. SIVERA 5010-L supplies a foam-control formulation to investigate. Follow foam knockdown, renewed foaming, particle distribution, settling and redispersion through the relevant processing and storage sequence.

Samples and Technical Support
LANDUSIL provides samples, TDS, SDS and ingredient-selection support for in-can development. Please include:
- Active ingredient, formulation type and continuous phase
- Salt or solvent load, pH and existing auxiliary package
- Mixing, milling and other manufacturing exposure
- Packaging, storage study, dilution water and target function
- Estimated quantity, packaging preference and destination country

