Electronics & Electrical
Silicone Ingredients for PCB Coatings
A populated circuit board needs a thin protective layer that follows component edges and preserves access to connectors. Silicone ingredients for PCB coatings help formulators develop that coverage through resin film formation or a reactive elastomeric network.
LANDUSIL supplies silicone resins, epoxy-siloxane binders and reactive PDMS for coating development. PCB coating manufacturers can compare these routes around their equipment, board materials, drying or cure window and repair process.

What Silicone Ingredients for PCB Coatings Do
- Provide a film-forming phase. Silicone resin and hybrid binder routes support coherent protective films.
- Build flexible coatings. Reactive PDMS provides a polymer base for elastic films across board features.
- Offer process choices. Supply form and carrier help you select a mixing and application route suited to your line.
- Support interface development. Binder selection brings adhesion to solder mask, component finishes and exposed inorganic surfaces into the formulation design.
- Enable selective coverage. Liquid flow and cure can be adjusted around edges, masking areas and the planned coating pattern.
Typical Uses
End use: Selective PCB coating
What matters most
Placement, liquid migration and consistent coverage near keep-out areas
End use: External component protection
What matters most
Edge coverage and cure around changes in surface height
End use: Metal, glass and ceramic regions
What matters most
Actual finish, cleaning history and conditioned adhesion
End use: Boards with connectors
What matters most
Masking compatibility and clean contact areas after removal
End use: Elastic protective films
What matters most
Polymer network, local thickness and board temperature limits
End use: Repairable coated assemblies
What matters most
Controlled removal, residue and replacement-coating behavior
Recommended LANDUSIL Products
LANDUSIL NOVERA 2010-L-XY60 represents a resin-solution route. The PDMS grades below represent polymer routes with their own crosslinking and catalytic packages.
| Product | Chemistry | CAS | Why choose it |
|---|---|---|---|
| NOVERA 2010-L-XY60 | Methyl phenyl silicone resin, xylene solution | Mixture – see SDS | Resin binder for solvent-based film development |
| NOVERA 4010-L | Epoxy polysiloxane resin | See SDS | Epoxy-functional resin route with a matched hardener |
| NOVERA 4020-L | Epoxy-siloxane blend binder | Mixture – see SDS | Blend-binder approach for studying film and phase behavior |
| DUVERA 5060-L | Hydroxyl-terminated PDMS | 70131-67-8 | Base polymer for a condensation-cure elastic film |
| DUVERA 5020-L | Vinyl-terminated PDMS | 68083-19-2 | Base polymer for an addition-cure elastic film |
How to Select a PCB Coating Route
Resin and hybrid films
Choose resin supply form with the deposition process in mind. A resin solution requires carrier evaporation and the appropriate film-development or cure step. An epoxy polysiloxane resin requires confirmed epoxy functionality and a compatible hardener. A blend binder adds composition and phase stability to the selection questions.
Condensation-cure PDMS films
Select the silanol polymer by actual viscosity and hydroxyl content, then establish its crosslinker, catalyst and adhesion package. Match moisture access and reaction-product removal to the deposited film. Include local thick areas beneath overhangs when planning the coating process.
Addition-cure PDMS films
Pair the vinyl polymer with a defined Si–H component and matched catalyst. Calculate reactive equivalents for the full mixture and choose a cure window the populated board can tolerate. Thin-film wetting and flow need attention even when a similar polymer works well in bulk potting.
Supply form and equipment
Compare atomization, dispensing or coating behavior on your equipment. A solvent route brings plastics, markings and trapped carrier into the assessment. Waterborne development adds dispersion stability, drying and residual components. A high-solids route places greater emphasis on controlling deposited thickness and flow before cure.
Application and Evaluation Guidelines
Begin with representative boards and controlled clean references. Include solder mask, component finishes, processing residues and the masking materials used on the production line. Surface contamination can affect adhesion, cure and electrical behavior beneath an apparently continuous film.
Measure dry-film thickness and inspect edges, pinholes, bubbles, bridging and dewetting. Check the cure in locally thicker or sheltered areas as well as exposed surfaces. For addition cure, investigate contact inhibition from the actual surface treatments, residues and adjacent materials.
Assess extractable ions or other relevant cleanliness measures, then compare electrical response under the specified humidity, temperature and bias. Water repellency alone does not establish electrical protection. Waterborne or solvent-free positioning cannot supply a low-ion or low-outgassing specification; evaluate the complete formulation and deposited film.
Include repair and recoating in the same program. Examine removal damage, residual material, replacement-film adhesion and electrical recovery after conditioning. Any finished-coating qualification belongs to the tested formulation and assembly.

Frequently Asked Questions
Which silicone materials are used in conformal coatings?
Resin binders, hybrid binders and reactive PDMS support different formulation routes. Choose resin film formation, condensation-cure elastomer or addition-cure elastomer according to your application and cure equipment.
How do I choose between a resin coating and elastic PDMS?
Compare the required film response, dry-film thickness, application method and repair needs. Then select the binder or network chemistry and develop it on representative board surfaces.
What causes gaps around PCB component edges?
Liquid flow, surface wetting, board geometry and cure progression affect edge coverage. Inspect representative height changes and keep-out areas while adjusting the application process.
How should a repaired conformal coating be evaluated?
Inspect the removed region for damage and residue, apply the intended replacement coating, and assess adhesion, cure and electrical behavior after the relevant conditioning.

Samples and Technical Support
LANDUSIL provides samples, TDS, SDS and selection support for protective-film development. Include:
- Board, component and surface-finish details
- Target film thickness, equipment and masking pattern
- Carrier preferences and drying or cure limits
- Current defects, repair method and electrical evaluation plan
- Expected quantity, packaging preference and destination country

