Industrial Release Agents
Silicone for Thermoset Mold Release
A thermoset develops its network while contacting the mold, so the release layer must work through resin flow and cure. Silicone for thermoset mold release supplies fluid and resin options for developing an external interface suited to that sequence. The useful result combines removal, surface reproduction and the required condition of the cured part.
LANDUSIL supplies PDMS, modified silicone fluids and MQ resin ingredients for thermoset compression release and resin casting. Match the material to the resin, cure package, filler and tool finish. This page covers tool-applied coatings for phenolic, amino-resin, epoxy and unsaturated-polyester systems.

What Silicone Ingredients Do for Thermoset Release
- Provide a lubricating external phase. Silicone fluid supports movement at the contacting surfaces as the cured part leaves the tool.
- Allow application behavior to be adjusted. Viscosity and carrier selection influence coverage across the mold and its detailed features.
- Offer organic-modification choices. Alkyl- and phenyl-containing fluids provide different chemistry routes for formulation and contact studies.
- Support resin-containing film development. MQ resin lets you investigate cohesion and tack in the working release layer.
- Connect surface quality with process control. A documented film-application sequence supports comparison of release, surface cure and molding compound deposits.
Typical Uses
End use: Phenolic compression molding
What matters most
Charge condition, flow, venting, cure at the mold and surface finish
End use: Amino-resin molding
What matters most
Actual compound and cure package, tool condition and local surface integrity
End use: Mineral-filled epoxy casting
What matters most
Filler condition, resin-rich surface, reaction history and epoxy casting release
End use: Unsaturated-polyester compression molding
What matters most
Compound form, fillers and any internal release ingredients already present
End use: Molded thermoset parts for finishing
What matters most
Release residue, cleaning and compatibility with paint, ink or adhesive
Recommended LANDUSIL Products
| Product | Chemistry | CAS | Why choose it |
|---|---|---|---|
| LANDUSIL DUVERA 1010-L | Polydimethylsiloxane, dimethyl silicone fluid | 63148-62-9 | Fluid phase for selecting coverage and studying retention during the thermoset molding cycle |
| LANDUSIL DUVERA 2010-L | Alkyl-modified silicone fluid | See SDS | Organic-modification option for blends containing waxes or other organic release components |
| LANDUSIL NOVERA 3020-S | MQ silicone resin, trimethylsiloxysilicate | 56275-01-5 | Resin phase for balancing film structure, tack and separation against the curing compound |
| LANDUSIL DUVERA 6030-L | Methylphenyl silicone fluid | 63148-58-3 | Phenyl-containing fluid option for process-specific compatibility and tool-interface studies |
How to Select Silicone for Thermoset Mold Release
Define the resin, filler and cure package
Provide the actual compound or casting formulation, including catalysts and internal processing additives. Phenolic molding release ingredients must be assessed with the phenolic compound in use. Apply the same formulation-specific approach to amino resins, epoxy and polyester.
For compression molding, record charge preparation, closing, pressure, venting and thermal history. For casting, record filling, resin contact, heat development and removal stage. These details describe the interface more usefully than a nominal mold temperature by itself.
Match the external layer to the tool
Inspect tool material, plating, finish and wear. Locate sticking or marking and compare it with repaired regions, difficult features and changes in the contacting resin. Select the actual PDMS viscosity around spreading and the deposited film. For modified fluids, establish modification and blending behavior with the intended auxiliaries.
Set an application method that reaches recesses and textures consistently. Record the interval for carrier removal before loading the reactive material, especially at regions receiving repeated overspray.
Choose fluid replenishment or a retained coating
A fluid-based external thermoset release layer is maintained through application and replenishment. A baked or reactive film needs its own film-forming route and curing sequence. Establish the mechanism and then assess film attachment to the tool, release from the resin and transfer to the part as individual objectives.
Mineral-Filled Thermoset Molding Compounds covers the material formulation. The tool-interface work here can be coordinated with that development while keeping the addition point clear.
Application and Evaluation Guidelines
Compare each complete release formulation with the production reference under controlled molding or casting conditions. Record coating history and carrier removal. Inspect the tool-facing resin for softness, tack, discoloration, porosity and texture changes, using the required cure measurements where useful.
Follow removal behavior, part damage, dimensional results and deposits through repeated runs. Include vents, parting lines and detailed regions in the inspection, then carry out the intended touch-up and cleaning sequence. Investigate tool wear, incomplete cure and mechanical locking when interpreting sticking.
MQ resin may increase tack; ordinary MQ does not establish vinyl functionality, self-curing behavior or a durable coating. A phenyl-fluid description does not define a qualified thermoset processing temperature. Verify downstream printing, painting or bonding on the molded parts after the planned cleaning. Use the full trial to establish application amount and maintenance, rather than treating easy initial removal as a complete acceptance result.

Frequently Asked Questions
Which silicone ingredients can I evaluate for thermoset compression molding?
PDMS and modified silicone fluids provide external fluid-phase options. MQ resin can be incorporated into a designed film. Compare complete formulations with the actual compound, cure package and tool.
How does release development differ between compression molding and casting?
Compression molding includes charge preparation, pressure, flow and venting. Casting adds its own filling, contact and reaction-heat history. Reproduce the intended sequence when evaluating the release layer.
What should I inspect when a thermoset part sticks?
Locate the sticking and inspect tool finish, wear, geometry and resin cure at that region. Compare these observations with release coverage and the history of deposits or cleaning.
How do I evaluate a release formulation for painted thermoset parts?
Prepare representative moldings, clean them using the planned method and apply the intended coating. Assess wetting, appearance and adhesion after the relevant conditioning alongside the release results.

Samples and Technical Support
LANDUSIL provides samples, TDS, SDS and formulation-selection support for thermoset release development. Please include:
- Resin, cure package, filler system and existing internal additives
- Compression or casting sequence, tool finish and thermal history
- Application and cleaning method, deposits and required downstream processing
- Estimated quantity, packaging preference and destination country

