Electronics & Electrical
PDMS Ingredients for Microfluidic Replication
Microchannels and thin valve membranes need to preserve their shape through casting, cure, release and assembly. PDMS ingredients for microfluidic replication let developers design the network around those features and the liquid that will contact the finished structure.
LANDUSIL supplies reactive silicone polymers, Si–H components, vinyl resin and functional silanes for fabrication studies. Microfluidic and microstructure developers can select casting ingredients and a subsequent interface treatment around the required geometry, mechanical response and device function.

What PDMS Ingredients for Microfluidic Replication Do
- Build an elastic casting network. Vinyl polymer and a matched Si–H component provide a reactive framework for replication.
- Support mechanical adjustment. Polymer and resin choices give you variables for membrane and channel-wall response.
- Enable detailed filling studies. Formulation flow can be developed around narrow mold features and thin regions.
- Provide functional interface options. Selected amino or epoxy silanes support suitable surface-treatment studies after defining the exposed surface.
- Connect fabrication with use. Material selection can address feature retention, bonding and interaction with the working liquid.
Typical Uses
End use: Microchannel replication
What matters most
Feature filling, trapped air and dimensions after release
End use: Elastic valve membranes
What matters most
Actual thickness, support geometry and repeated actuation
End use: Optical microstructures
What matters most
Replicated surface, wavelength, thickness and optical function
End use: Glass–PDMS bonding studies
What matters most
Prepared surfaces, alignment and channel accessibility
End use: Fluid-contact microdevices
What matters most
Swelling, solute partitioning, surface adsorption and extractables
Recommended LANDUSIL Products
LANDUSIL DUVERA 5020-L supplies the vinyl-terminated casting polymer. The silanes below serve a defined interface-treatment role with appropriate surface chemistry and reaction partners.
| Product | Chemistry | CAS | Why choose it |
|---|---|---|---|
| DUVERA 5020-L | Vinyl-terminated PDMS | 68083-19-2 | Polymer base for a designed addition-cure replication material |
| DUVERA 4020-L | Methylhydrosiloxane-dimethylsiloxane copolymer | 68037-59-2 | Si–H reaction partner selected by actual reactive content |
| NOVERA 3010-L | Vinyl MQ silicone resin | See SDS | Reactive resin for network and mechanical-response studies |
| LEGRA 2010-L | 3-Glycidoxypropyltriethoxysilane | 2602-34-8 | Epoxy-functional treatment for an appropriate prepared surface |
| LEGRA 1010-L | 3-Aminopropyltriethoxysilane | 919-30-2 | Amino-functional surface treatment with a defined subsequent reaction |
How to Select a Microreplication Material
Let the feature define the formulation
Specify channel dimensions, mold features, membrane thickness and the support structure. For a valve, include the required movement and sealing task. For an optical microstructure, include the light path, wavelength and replicated surface requirements.
Design the full network
Use actual vinyl and Si–H equivalents and include reactive resin in the calculation. Select a matched catalyst and inhibitor package around the filling and cure window. Compare the resulting network response with the flexibility and dimensional requirements of the replicated part.
Coordinate filling, cure and release
Observe flow and air removal over the casting period, using representative corners and thin regions. Record mixing, transfer and cure history. Screen the mold and release treatment for cure-contact compatibility. Silicone Molding and Soft-Tool Release develops the mold-release interface task.
Choose the bonding or functional surface step
Identify the actual exposed surface and complementary chemistry for a silane treatment. Plan the surface preparation and post-treatment around the later bond or function. Sensor and Microdevice Surface Silanization addresses molecular functionalization and its relation to sensor response.
Application and Evaluation Guidelines
Compare clean cure references with the actual mold, release coating and adjacent materials. Inspect local cure at contact surfaces as well as the bulk. A commercial casting kit's mass ratio does not define the reactive-equivalent balance for these individual raw materials.
Measure channel geometry, tears and surface defects after release. Check bonded interfaces, continuity, alignment and leakage under the intended operating conditions. Softness does not establish valve sealing, and successful release cannot establish the later fluidic bond.
Keep amino or epoxy interface treatments distinct from the vinyl/Si–H casting reaction. Screen amino contact around uncured platinum systems. Record wetting after treatment with elapsed time and storage history; initial hydrophilicity requires a stability study for the actual formulation and thickness.
Evaluate the real liquid composition, exposure time and temperature. Distinguish swelling, solute absorption into PDMS, surface adsorption and extraction of mobile species. Low visible swelling does not establish unchanged analyte concentration. If conditioning or extraction is used, evaluate the treated material and final device for their intended function and purity requirements.

Frequently Asked Questions
Which raw materials form an addition-cure PDMS replication material?
A vinyl-functional polymer, matched Si–H component and catalyst provide the network. A reactive vinyl resin can be included to study mechanical response and processing behavior.
How should a microfluidic valve membrane be evaluated?
Measure actual thickness and mechanical response in the supporting geometry. Check actuation, closure, sealing and behavior through repeated deformation.
What should be checked after bonding a PDMS channel to glass?
Inspect alignment, channel continuity and the complete bonded interface. Evaluate leakage and deformation under the intended operating and liquid-exposure conditions.
Why should liquid compatibility include more than swelling?
Solutes can partition into PDMS and mobile material can be extracted from it. Measure the fluid and device response as well as dimensional change when concentration or cleanliness matters.

Samples and Technical Support
LANDUSIL provides samples, TDS, SDS and network or interface ingredient support. Include:
- Feature geometry, membrane target and mold material
- Mixing, casting, cure and release requirements
- Bonding route and prepared surface
- Working liquid, exposure and functional measurements
- Estimated quantity, packaging preference and destination country

